Airpulse A300 Support
Premium Hi-Res active speakers designed by Phil Jones
Frequently Asked Questions
Yes, you can use a subwoofer with our powered speakers, but the subwoofer must also be self-powered. You will need an RCA Y-splitter. From the audio source run one set of the RCA’s to the speakers, and the other set of RCA’s to the subwoofer. Note that speakers without a sub-out do not have a low-pass filter, so they will continue to play bass frequencies when connected to the subwoofer.
This is possible but only if the audio source is capable of dual Bluetooth audio. Please check with your Bluetooth devices owner’s manual, or the manufacturer to see if it has dual Bluetooth audio capability. If your device does not have this capability you can purchase an external Bluetooth splitter transmitter from many online retailers.
This issue is usually caused by a tracking issue on the turntable. To test if it is the turntable at fault or the speakers, reverse the RCA jacks on the control speaker, red to white and white to red. If the issue now occurs on the other speaker, it is the turntable at fault. Please contact your turntable manufacturer for instructions on how to properly set the tracking. If the issue remains on the same channel it is problem. Please contact our customer service team for troubleshooting and assistance.
1. Make sure the Bluetooth input is selected, you can do this one of two ways. With the speaker remote, press the button with the Bluetooth symbol or you can click-in the volume knob on the control speaker to cycle through the inputs. If the speakers have an LED indicator the light will turn blue, if they have a screen the Bluetooth symbol will appear, you will now be able to pair a device. If you are able to pair, but are still not getting audio please check that the volume is up on both the Bluetooth device and the speakers. 2. Disconnect any previously paired devices. Press and hold the volume knob down on the control speaker for 2-5 seconds. Then pair with the speakers from your Bluetooth device. 3. Try resetting the Bluetooth chip to factory settings. Please unplug the speakers for at least ten minutes to allow for the capacitors to fully drain. Then plug the speakers back in, select the Bluetooth input, and pair your device with the speakers. *If none of the above troublehooting works, then it is most likely an issue with the speakers Bluetooth chip, and the speakers will need to be replaced.
Self-powered speakers require a Pre-amp to boost the phono signal to a line-level. Many modern turntables come with a built-in switchable pre-amp. Usually the switch to turn on the pre-amp is either on the back of the turntable, or underneath the platter. The switch is most commonly labelled Phono/Line, it will need to be in the Line position. To find out if your turntable has a built-in pre-amp please refer to the owner’s manual, or contact the manufacturer.
In order to protect the speakers (and your ears) from a loud volume surge, they utilize a volume remember setting that powers on at anywhere from 20 to 60% lower volume, depending on how loud they were when they were last switched off.
Remotes are available for purchase on Edifier’s official website. Visit the Edifier site that is specific to your region and then click the “Shop” at the top right. On the next page, click on “Accessories” located in the left sidebar. The accessories page should have a listing for the remote.
1. Check that the optical input is selected on the speakers, for speakers with an LED indicator the light will be red, for speakers with a screen, OPT will be displayed. 2. Our speakers use Pulse-Code Modulation, or PCM as the optical/digital input signal. TV’s with an optical audio output will have the option to switch the optical/digital output to PCM. This can usually be done by going into the audio settings, or advanced audio settings, on the TV menu. If you cannot find the setting for your particular brand and model of TV, please contact the manufacturer, they will easily be able to walk you through the process of switching to PCM.
1. Are the speakers plugged into a working outlet and the master power switch on the active speaker is switched to on? Can you try the speakers with a few different outlets? Is the LED indicator on the speaker no longer coming on once you do this? 2. If the speakers are turning on can you try using them with a few different inputs and audio sources to see if you can get them to play? Also be sure to check the the input you are using to connect to the speakers is selected using the remote or volume knob. *If the speakers will not turn on after checking the power switch and making sure the outlet is working, the internal power supply is most likely bad and the speakers will need to be replaced if they are under warranty.
From the source you will want to run 2 RCA single male to dual female RCA splitters, one in the left channel one in the right channel. Using 4 single male-to-male RCA cables(Tip: if you have 2 dual male-to-male RCA cables you can split them down the middle to get 4 singles), run a left channel to the subwoofer and left channel to the speakers. Using the other 2 male-to-male RCA cables run one right channel to the speakers, and one right channel to the subwoofer.
Most Bluetooth receivers have Bluetooth input only, meaning you can stream from your audio device to the receiver and it will output the sound through a wired connection. Some receivers do have Bluetooth output, but it is not common. Please confirm with the receiver manufacturer if your model has Bluetooth output.
" Speakers disconnect from the Bluetooth input. To get it back on and have the ability to pair with the speakers these are the steps: 1. Locate the volume knob on the active speaker. 2. Click the volume knob in very quickly, like you are clicking a computer mouse. 3. Each click will cycle between the inputs, once the LED indicator light is blue the Bluetooth input will be selected. 4. Pair your device with the speakers. "
You can switch the inputs by clicking the volume knob on the control speaker. This will cycle through the different inputs.
First, check if your device requires a driver update. If not, then this is often an issue with the operating system rather than the products themselves. We suggest contacting Windows support for help. The phone number for their US support line is 1 (800) 642 7676. You can also visit their help page, and click on “Contact Support” under the “Get Help” app button: https://support.microsoft.com/en-us/contactus/ For a full international list of Microsoft support numbers, please visit this page: https://support.microsoft.com/en-us/help/4051701/global-customer-service-phone-numbers
1. Please check that the USB input is selected. USB will be displayed on the control speakers input screen. 2. For Mac users, please open “System Preferences,” select the “Sound” tab, and select the Edifier speakers as the current audio output device. 3. For Microsoft Windows 7/10 users, please download and install the Windows audio drivers. The drivers can be found here: NOTE if possible, please include a link to the XMOS audio drivers here. Then open the control panel, select “Sound,” and set the audio output device to the Edifier speakers or XMOS USB Audio.
"Disable the absolute volume function on the computer by following these steps. 1. Open Windows Registry (search for regedit.exe). 2. Click on Computer>HKEY_LOCAL_MACHINE>SYSTEM>ControlSet001>Control>Bluetooth>Audio>AVRCP>CT 3. Then click on DisableAbsoluteVolume and set the value to 1"
You will need to disable absolute volume in the phone. First, enable developer options. To do this, go to Device Settings, then scroll down and select "About Phone. " From there, tap on "Software Information" and locate the "Build Number" entry. Once you've found it, tap on "Build Number" seven times in rapid succession, developer options will then be available on the settings menu of the phone. Go into developer options and toggle the button for "disable absolute volume." Restart the phone and this should allow you to control the volume of the speakers from the phone.
The S1000DB is one of the top of the line bookshelf 2.0 models from Edifier. It will have a better sound than other non S series or Airpulse models.